Skip to main content
Scullcom
  • Home
  • Projects
    • All Projects
    • 5 Volt Precision Reference
    • Constant Current Source Box
    • DC Load
    • DC Voltage Calibrator
    • DIY PCB Exposure Unit
    • Frequency Reference
    • Function Generator
    • Function Generator Mk2
    • GPS System
    • LED Floodlight
    • Low Current Reference
    • Milliohm Meter
    • Millivolt Meter
    • Precision Voltage Reference Box
    • Stair-Step Waveform Generator
    • Pulse Generator
  • Reviews
  • Teardowns
  • Tutorials
  • Basics
    • Resistor
    • Capacitor
    • Inductor
    • Diode
    • Opto
    • Transistor
    • OP Amp
    • Logic Gates
    • Filters
    • Sensors
    • Fuses
    • Batteries
    • Transformer
    • Antenna
  • About

Category: Frequency Reference

Design & Build a GPS locked Frequency Standard – Part 4

24th March 201629th March 2016 Louis Scully 39 Comments

In this 4th part of this project we upgrade the software to give satellite data and frequency lock display. Plus the current frequency on the display is improved to give reading in MHz, KHz or Hz. The new software version can be downloaded from the link below: http://www.scullcom.com/GPS_Ref_Version6.zip PLEASE NOTE TO COMPILE THIS CODE YOU […]

Read More

Design & Build a GPS locked Frequency Standard – Part 3

6th March 201624th March 2016 Louis Scully 4 Comments

In Part 3 of this project we will add a keypad for direct frequency entry and program the GPS module on the fly directly from the Arduino Nano. We will also add a battery check feature and make some changes to the original circuit. A new PCB design will allow all components to be on […]

Read More

Design & Build a GPS locked Frequency Standard – Part 2

5th March 201612th March 2016 Louis Scully 1 Comment

  In Part 2 of this project we will improve the reception of the GPS module and build the project on to printed circuit boards and test the unit. In addition we will look at ways of converting the 10MHz square wave to a sine wave. Below are links to download the schematics and PCB […]

Read More

Design & Build a GPS locked Frequency Reference Standard – Part 1

16th February 201612th March 2016 Louis Scully 5 Comments

In this project we will design and build a 10MHz GPS locked frequency standard with additional outputs of 1MHz, 100KHz, 10KHz, 1KHz and 100Hz. The output frequency will also be present even when no satellite lock is available but will be free running. We will use a Arduino Nano and LCD display to indicate if […]

Read More

Categories

  • 5 Volt Precision Reference
  • Basics
  • Constant Current Source Box
  • DC Load
  • DC Voltage Calibrator
  • DIY PCB Exposure Unit
  • Frequency Reference
  • Function Generator
  • Function Generator Mk2
  • GPS System
  • LED Floodlight
  • Low Current Reference
  • Milliohm Meter
  • Millivolt Meter
  • OP Amp
  • Precision Voltage Reference Box
  • Projects
  • Pulse Generator
  • Resistor
  • Reviews
  • Stair-Step Waveform Generator
  • Teardowns
  • Tutorials
  • Uncategorised
  • ZX80

Archives

  • August 2018
  • December 2017
  • June 2017
  • December 2016
  • November 2016
  • September 2016
  • June 2016
  • May 2016
  • March 2016
  • February 2016
  • January 2016
  • December 2015
  • October 2015
  • September 2015
  • August 2015
  • July 2015
  • May 2015
  • April 2015
  • March 2015
  • February 2015

Recent Comments

  • Umberto Marcucci on DC Voltage Calibrator
  • Šoaslav Negraubil on Function Generator Mk2
  • Steven on Design & Build a Milliohm Meter
  • Colin on Design & Build an Electronic DC Load
  • Chris Schouten on Design & Build a Milliohm Meter

Meta

  • Log In
  • Posts RSS
  • Posts RSS
Scullcom.uk all lefts reversed Theme by Colorlib Powered by WordPress